Futaba 14 SG + F450 NAZA V2 ...grrrrrrrr!

Discussion in 'DJI NAZA flight control system' started by Totuccio, Dec 11, 2013.

  1. Totuccio

    Totuccio New Member

    Joined:
    Dec 11, 2013
    Messages:
    31
    HI guys

    I have since few days a new Futaba 14SG and a DJI F450 naza v2 with firmware 4.02 , but I dont understand how I can set up the futaba , can someone that use already has this RC with a DJI F450 naza v2 can send me the setting file , it would be very nice ...

    regards
     
  2. badtoys

    badtoys New Member

    Joined:
    Nov 16, 2013
    Messages:
    31
    RTFM


    Enviado desde mi iPad con Tapatalk HD
     
  3. Totuccio

    Totuccio New Member

    Joined:
    Dec 11, 2013
    Messages:
    31
    what does it means " RTFM " ?
     
  4. COMike93yj

    COMike93yj Still Building!

    Joined:
    Nov 18, 2013
    Messages:
    265
    Location:
    Front Range, Colorado
    It means "Read The Full Manual". Some folks insert another word for "full"

    I wish I could help but have no experience with your setup.
     
  5. Totuccio

    Totuccio New Member

    Joined:
    Dec 11, 2013
    Messages:
    31
    ok I did it but it is not so easy , I am new in this hobby , I was thinking forums are made to help people when they have problems , an answer with RTFM is silly ,
     
  6. COMike93yj

    COMike93yj Still Building!

    Joined:
    Nov 18, 2013
    Messages:
    265
    Location:
    Front Range, Colorado
    I agree with you Totuccio...it was not a helpful response. Have you looked at the other areas of the forum? I think this is a good area but maybe ask in the futaba area in another forum? Hopefully someone can come and help!
     
    Last edited by a moderator: Dec 11, 2013
  7. AboveAllAP

    AboveAllAP Member

    Joined:
    Mar 28, 2013
    Messages:
    161
    Location:
    Brisbane Australia
    OK I tend to agree with the comment RTFM... however I do also understand it is a steep learning curve. Reading the f'n manual will hopefully give you a full and better understanding of everything. It is crazy and not to mention potentially dangerous to take one of these craft up into the sky without first having a good understanding and knowledge of what it is you are doing. There are many great videos on youtube and DJI's website which give step by step instructions on how to setup a Naza with a Futaba controller. I suggest you give those a try. I have read and re read the manuals many times and will refer back to them for refreshers. If and when things go wrong it pays to know how to deal with it. knowing how and why everything hangs together will make this hobby much more enjoyable and probably less costly for you.
     
  8. COMike93yj

    COMike93yj Still Building!

    Joined:
    Nov 18, 2013
    Messages:
    265
    Location:
    Front Range, Colorado
    I too think everyone must RTFM however a single post of RTFM is a curt and snarky response. Good suggestions for Totuccio to check out YouTube and DJI website as well!
     
  9. badtoys

    badtoys New Member

    Joined:
    Nov 16, 2013
    Messages:
    31
    RTFM is the best advice anyone can give you. I'm a newbie too with less than 1 year on this. I lost a DJI F550 becuose I don't read the FULL manual and understand how to setup correctly the failsafe function on my radio.

    So take it seriusly and RTFM.


    Enviado desde mi iPad con Tapatalk HD
     
  10. econfly

    econfly Blogging Enabled

    Joined:
    Sep 2, 2013
    Messages:
    266
    Put the receiver in mode "D" (hold button while powering on, then release and press until 4 flashes on the LED holding down on the 4th flash). Connect one servo cable from the receiver to the NAZA using the single low horizontal "SBUS2" port on the receiver. Link the receiver to the radio. A sample model file is attached (ignore the ".txt" extension -- this is a Futaba formatted model file that you can upload to your radio). Of course, confirm that everything is working correctly in your NAZA software before using.
     

    Attached Files:

    Last edited by a moderator: Dec 11, 2013

Share This Page